a10_interface_ve

Synopsis

Virtual ethernet interface

Parameters

Parameters		Choices/Defaults	Comment
state str/required		[‘noop’, ‘present’, ‘absent’]	State of the object to be created.
ansible_host str/required			Host for AXAPI authentication
ansible_username str/required			Username for AXAPI authentication
ansible_password str/required			Password for AXAPI authentication
ansible_port int/required			Port for AXAPI authentication
a10_device_context_id int		[‘1-8’]	Device ID for aVCS configuration
a10_partition str			Destination/target partition for object/command
ifnum int/required			Virtual ethernet interface number
name str			Name for the interface
port_scan_detection str			‘enable’= Enable port scan detection; ‘disable’= Disable port scan detection(default);
ping_sweep_detection str			‘enable’= Enable ping sweep detection; ‘disable’= Disable ping sweep detection(default);
l3_vlan_fwd_disable bool			Disable L3 forwarding between VLANs for incoming packets on this interface
mtu int			Interface mtu (Interface MTU, default 1 (min MTU is 1280 for IPv6))
trap_source bool			The trap source
action str			‘enable’= Enable; ‘disable’= Disable;
icmp_rate_limit dict			Field icmp_rate_limit
	normal int		Normal rate limit. If exceeds this limit, drop the ICMP packet that goes over the limit
	lockup int		Enter lockup state when ICMP rate exceeds lockup rate limit (Maximum rate limit. If exceeds this limit, drop all ICMP packet for a time period)
	lockup_period int		Lockup period (second)
icmpv6_rate_limit dict			Field icmpv6_rate_limit
	normal_v6 int		Normal rate limit. If exceeds this limit, drop the ICMP packet that goes over the limit
	lockup_v6 int		Enter lockup state when ICMP rate exceeds lockup rate limit (Maximum rate limit. If exceeds this limit, drop all ICMP packet for a time period)
	lockup_period_v6 int		Lockup period (second)
access_list dict			Field access_list
	acl_id int		ACL id
	acl_name str		Named Access List
uuid str			uuid of the object
user_tag str			Customized tag
sampling_enable list			Field sampling_enable
	counters1 str		‘all’= all; ‘num_pkts’= Input packets; ‘num_total_bytes’= Input bytes; ‘num_unicast_pkts’= Received unicasts; ‘num_broadcast_pkts’= Received broadcasts; ‘num_multicast_pkts’= Received multicasts; ‘num_tx_pkts’= Transmitted packets; ‘num_total_tx_bytes’= Transmitted bytes; ‘num_unicast_tx_pkts’= Transmitted unicasts; ‘num_broadcast_tx_pkts’= Transmitted broadcasts; ‘num_multicast_tx_pkts’= Transmitted multicasts; ‘rate_pkt_sent’= Packet sent rate packets/sec; ‘rate_byte_sent’= Byte sent rate bits/sec; ‘rate_pkt_rcvd’= Packet received rate packets/sec; ‘rate_byte_rcvd’= Byte received rate bits/sec; ‘load_interval’= Load Interval;
ip dict			Field ip
	dhcp bool		Use DHCP to configure IP address
	address_list list		Field address_list
	allow_promiscuous_vip bool		Allow traffic to be associated with promiscuous VIP
	client bool		Client facing interface for IPv4/v6 traffic
	server bool		Server facing interface for IPv4/v6 traffic
	helper_address_list list		Field helper_address_list
	inside bool		Configure interface as inside
	outside bool		Configure interface as outside
	ttl_ignore bool		Ignore TTL decrement for a received packet
	syn_cookie bool		Enable SYN-cookie on the interface
	slb_partition_redirect bool		Redirect SLB traffic across partition
	generate_membership_query bool		Enable Membership Query
	query_interval int		1 - 255 (Default is 125)
	max_resp_time int		Maximum Response Time (Max Response Time (Default is 100))
	uuid str		uuid of the object
	stateful_firewall dict		Field stateful_firewall
	router dict		Field router
	rip dict		Field rip
	ospf dict		Field ospf
ipv6 dict			Field ipv6
	address_list list		Field address_list
	ipv6_enable bool		Enable IPv6 processing
	v6_acl_name str		Apply ACL rules to incoming packets on this interface (Named Access List)
	inbound bool		ACL applied on incoming packets to this interface
	inside bool		Configure interface as NAT inside
	outside bool		Configure interface as NAT outside
	ttl_ignore bool		Ignore TTL decrement for a received packet
	router_adver dict		Field router_adver
	uuid str		uuid of the object
	stateful_firewall dict		Field stateful_firewall
	router dict		Field router
	rip dict		Field rip
	ospf dict		Field ospf
ddos dict			Field ddos
	outside bool		DDoS inside (trusted) or outside (untrusted) interface
	inside bool		DDoS inside (trusted) or outside (untrusted) interface
	uuid str		uuid of the object
nptv6 dict			Field nptv6
	domain_list list		Field domain_list
map dict			Field map
	inside bool		Configure MAP inside interface (connected to MAP domains)
	outside bool		Configure MAP outside interface
	map_t_inside bool		Configure MAP inside interface (connected to MAP domains)
	map_t_outside bool		Configure MAP outside interface
	uuid str		uuid of the object
lw_4o6 dict			Field lw_4o6
	outside bool		Configure LW-4over6 inside interface
	inside bool		Configure LW-4over6 outside interface
	uuid str		uuid of the object
bfd dict			Field bfd
	authentication dict		Field authentication
	echo bool		Enable BFD Echo
	demand bool		Demand mode
	interval_cfg dict		Field interval_cfg
	uuid str		uuid of the object
isis dict			Field isis
	authentication dict		Field authentication
	bfd_cfg dict		Field bfd_cfg
	circuit_type str		‘level-1’= Level-1 only adjacencies are formed; ‘level-1-2’= Level-1-2 adjacencies are formed; ‘level-2-only’= Level-2 only adjacencies are formed;
	csnp_interval_list list		Field csnp_interval_list
	padding bool		Add padding to IS-IS hello packets
	hello_interval_list list		Field hello_interval_list
	hello_interval_minimal_list list		Field hello_interval_minimal_list
	hello_multiplier_list list		Field hello_multiplier_list
	lsp_interval int		Set LSP transmission interval (LSP transmission interval (milliseconds))
	mesh_group dict		Field mesh_group
	metric_list list		Field metric_list
	network str		‘broadcast’= Specify IS-IS broadcast multi-access network; ‘point-to-point’= Specify IS-IS point-to-point network;
	password_list list		Field password_list
	priority_list list		Field priority_list
	retransmit_interval int		Set per-LSP retransmission interval (Interval between retransmissions of the same LSP (seconds))
	wide_metric_list list		Field wide_metric_list
	uuid str		uuid of the object
oper dict			Field oper
	state str		Field state
	line_protocol str		Field line_protocol
	link_type str		Field link_type
	mac str		Field mac
	ipv4_address str		IP address
	ipv4_netmask str		IP subnet mask
	ipv6_link_local str		Field ipv6_link_local
	ipv6_link_local_prefix str		Field ipv6_link_local_prefix
	ipv6_link_local_type str		Field ipv6_link_local_type
	ipv6_link_local_scope str		Field ipv6_link_local_scope
	ipv4_addr_count int		Field ipv4_addr_count
	ipv4_list list		Field ipv4_list
	ipv6_addr_count int		Field ipv6_addr_count
	ipv6_list list		Field ipv6_list
	igmp_query_sent int		Field igmp_query_sent
	icmp_rate_limit_current int		Field icmp_rate_limit_current
	icmp_rate_over_limit_drop int		Field icmp_rate_over_limit_drop
	icmp6_rate_limit_current int		Field icmp6_rate_limit_current
	icmp6_rate_over_limit_drop int		Field icmp6_rate_over_limit_drop
	user_trunk_id int		Field user_trunk_id
	ip_unnumbered_oper int		Field ip_unnumbered_oper
	ip_unnumbered_enabled int		Field ip_unnumbered_enabled
	ip_unnumbered_mac_learned int		Field ip_unnumbered_mac_learned
	ip_unnumbered_peer_lla str		Field ip_unnumbered_peer_lla
	ifnum int		Virtual ethernet interface number
stats dict			Field stats
	num_pkts str		Input packets
	num_total_bytes str		Input bytes
	num_unicast_pkts str		Received unicasts
	num_broadcast_pkts str		Received broadcasts
	num_multicast_pkts str		Received multicasts
	num_tx_pkts str		Transmitted packets
	num_total_tx_bytes str		Transmitted bytes
	num_unicast_tx_pkts str		Transmitted unicasts
	num_broadcast_tx_pkts str		Transmitted broadcasts
	num_multicast_tx_pkts str		Transmitted multicasts
	rate_pkt_sent str		Packet sent rate packets/sec
	rate_byte_sent str		Byte sent rate bits/sec
	rate_pkt_rcvd str		Packet received rate packets/sec
	rate_byte_rcvd str		Byte received rate bits/sec
	load_interval str		Load Interval
	ifnum int		Virtual ethernet interface number

Examples

Return Values

modified_values (changed, dict, )

Values modified (or potential changes if using check_mode) as a result of task operation

axapi_calls (always, list, )

Sequential list of AXAPI calls made by the task

endpoint (, str, [‘/axapi/v3/slb/virtual_server’, ‘/axapi/v3/file/ssl-cert’])

The AXAPI endpoint being accessed.

http_method (, str, [‘POST’, ‘GET’])

HTTP method being used by the primary task to interact with the AXAPI endpoint.

request_body (, complex, )

Params used to query the AXAPI

response_body (, complex, )

Response from the AXAPI

Status

• This module is not guaranteed to have a backwards compatible interface. [preview]

• This module is maintained by community.

Authors

• A10 Networks