a10_router_isis

Synopsis

Intermediate System - Intermediate System (IS-IS)

Parameters

Parameters		Choices/Defaults	Comment
state str/required		[‘noop’, ‘present’, ‘absent’]	State of the object to be created.
ansible_host str/required			Host for AXAPI authentication
ansible_username str/required			Username for AXAPI authentication
ansible_password str/required			Password for AXAPI authentication
ansible_port int/required			Port for AXAPI authentication
a10_device_context_id int		[‘1-8’]	Device ID for aVCS configuration
a10_partition str			Destination/target partition for object/command
tag str/required			ISO routing area tag
adjacency_check bool			Check ISIS neighbor protocol support
area_password_cfg dict			Field area_password_cfg
	password str		Configure the authentication password for an area (Area password)
	authenticate dict		Field authenticate
authentication dict			Field authentication
	send_only_list list		Field send_only_list
	mode_list list		Field mode_list
	key_chain_list list		Field key_chain_list
bfd str			‘all-interfaces’= Enable BFD on all interfaces;
default_information str			‘originate’= Distribute a default route;
distance_list list			Field distance_list
	distance int		ISIS Administrative Distance (Distance value)
	System_ID str		System-ID in XXXX.XXXX.XXXX
	acl str		Access list name
domain_password_cfg dict			Field domain_password_cfg
	password str		Set the authentication password for a routing domain (Routing domain password)
	authenticate dict		Field authenticate
ha_standby_extra_cost list			Field ha_standby_extra_cost
	extra_cost int		The extra cost value
	group int		Group (Group ID)
ignore_lsp_errors bool			Ignore LSPs with bad checksums
is_type str			‘level-1’= Act as a station router only; ‘level-1-2’= Act as both a station router and an area router; ‘level-2-only’= Act as an area router only;
log_adjacency_changes_cfg dict			Field log_adjacency_changes_cfg
	state str		‘detail’= Log changes in adjacency state; ‘disable’= Disable logging;
lsp_gen_interval_list list			Field lsp_gen_interval_list
	interval int		Minimum interval in seconds
	level str		‘level-1’= Set interval for level 1 only; ‘level-2’= Set interval for level 2 only;
lsp_refresh_interval int			Set LSP refresh interval (LSP refresh time in seconds)
max_lsp_lifetime int			Set maximum LSP lifetime (Maximum LSP lifetime in seconds)
metric_style_list list			Field metric_style_list
	ntype str		‘narrow’= Use old style of TLVs with narrow metric; ‘wide’= Use new style of TLVs to carry wider metric; ‘transition’= Send and accept both styles of TLVs during transition; ‘narrow-transition’= Send old style of TLVs with narrow metric with accepting both styles of TLVs; ‘wide-transition’= Send new style of TLVs to carry wider metric with accepting both styles of TLVs;
	level str		‘level-1’= Level-1 only; ‘level-1-2’= Level-1-2; ‘level-2’= Level-2 only;
passive_interface_list list			Field passive_interface_list
	ethernet str		Ethernet interface (Port number)
	loopback str		Loopback interface (Port number)
	trunk str		Trunk interface (Trunk interface number)
	lif str		Logical interface (Lif interface number)
	ve str		Virtual ethernet interface (Virtual ethernet interface number)
	tunnel str		Tunnel interface (Tunnel interface number)
protocol_list list			Field protocol_list
	protocol_topology bool		Protocol Topology
set_overload_bit_cfg dict			Field set_overload_bit_cfg
	set_overload_bit bool		Signal other touers not to use us in SPF
	on_startup dict		Field on_startup
	suppress_cfg dict		Field suppress_cfg
spf_interval_exp_list list			Field spf_interval_exp_list
	min int		Minimum Delay between receiving a change to SPF calculation in milliseconds
	max int		Maximum Delay between receiving a change to SPF calculation in milliseconds
	level str		‘level-1’= Set interval for level 1 only; ‘level-2’= Set interval for level 2 only;
summary_address_list list			Field summary_address_list
	prefix str		IP network prefix
	level str		‘level-1’= Summarize into level-1 area; ‘level-1-2’= Summarize into both area and sub-domain; ‘level-2’= Summarize into level-2 sub-domain;
net_list list			Field net_list
	net str		A Network Entity Title for this process (XX.XXXX. … .XXXX.XX Network entity title (NET))
uuid str			uuid of the object
user_tag str			Customized tag
redistribute dict			Field redistribute
	redist_list list		Field redist_list
	vip_list list		Field vip_list
	isis dict		Field isis
	uuid str		uuid of the object
address_family dict			Field address_family
	ipv6 dict		Field ipv6

Examples

Return Values

modified_values (changed, dict, )

Values modified (or potential changes if using check_mode) as a result of task operation

axapi_calls (always, list, )

Sequential list of AXAPI calls made by the task

endpoint (, str, [‘/axapi/v3/slb/virtual_server’, ‘/axapi/v3/file/ssl-cert’])

The AXAPI endpoint being accessed.

http_method (, str, [‘POST’, ‘GET’])

HTTP method being used by the primary task to interact with the AXAPI endpoint.

request_body (, complex, )

Params used to query the AXAPI

response_body (, complex, )

Response from the AXAPI

Status

• This module is not guaranteed to have a backwards compatible interface. [preview]

• This module is maintained by community.

Authors

• A10 Networks 2021